Description:
 • A double-pole double throw knife switch for connecting the motor / generator.
 • The socket terminals are labelled battery, motor and lamp respectively.
 • Dimensions of laminated wooden base 155 x 105 mm.
Product Code :- CLM/PHY/H-067

Description:
• With 3 M.E.S. Iamp sockets
• connected in parallel • On base with terminals
• With three lamps of 1,25 V,0.25 A
Product Code :- CLM/PHY/H-068

Description:
• For use with motor / generators to give an indication of their output when used as dynamos.
• The lamp holders are connected in parallel.
• Supplied with three lamps 3.5 V, 0.25 Amps. M.E.S.
Product Code :- CLM/PHY/H-069

Description:
• For use with a large motor / generator and a lamp unit to demonstrate the conversion of electrical energy to kinetic energy and then back again. Comprising an iron flywheel 115 mm. diameter,mass 1.2 kg. mounted in cast bracket with bearings. The shaft has an aluminium ‘V’ pulley 44 mm. diameter, for driving with the spring belt supplied.
Product Code :- CLM/PHY/H-070

Description:
• Complementary to CLM/PHY/H-070 having same mass but 50 mm diam,with 20 mm pulley, on base.
Product Code :- CLM/PHY/H-071

Descripition:
• For showing the conversion from electrical energy via mechanical to potential energy by winding up a weight on a cord.
• One end of the 6 mm steel shaft carries an aluminium• ‘V’ pulley 56 mm diameter and the other end is fitted with a cord anchoring collar.
• Supplied complete with driving belt.
• Size are 10 x 20 cm
Product Code :- CLM/PHY/H-072

Description:
• For showing potential energy in a wound-up spring and its conversion to electrical energy by driving a dynamo and lighting a lamp.
• Used to wind up a weight on a cord showing the change from potential energy to kinetic and back to potential in the raised weight.
• The steel shaft carries a clock spring with a free wheel device and
• Winding ratchet, also an aluminium ‘V’ pulley 56 mm diameter.
• One end of the shaft overhangs the base for use as line shaft when winding up a weight.
 • Dimensions 220 x 100 x 100 mm high.
• Supplied complete with driving belt.
• Size 10 x 20 cm
Product Code :- CLM/PHY/H-073

Description:
• For use with the large motor/Generator in comparing power input and output by driving each in turn with the other and metering the voltage and currents.
• Uses a smaller 1.5 to 4.5 V motor.
• Dimensions of laminated wooden base 155 x 105 mm.
Product Code :- CLM/PHY/H-074

Description:
• Comprises a 2 to 6V D.C.
• Motor provided with a 15 mm diameter V pulley.
• For use as a driving unit or dynamo.
• Dimensions of laminated wooden base 155 x 105 mm.
Product Code :- CLM/PHY/H-075

Description:
• Comprising a brass cylinder, internal size 27 x 16 mm diameter, with and integral V pulley in the base of the cylinder and a 6 mm diameter steel shaft which fits into a bearing block. A vertical pillar carries the cork lined friction arms and thermometer support. Supplied without thermometer. Dimensions of laminated wooden base 155 x 105 mm.
Product Code :- CLM/PHY/H-076

Description:
• The driving and output pulleys are both 75 mm diameter, and
• The intermediate pulley is 20 mm diameter giving a step up ratio of 3.75.
• Dimensions of laminated wooden base 155 x 105 mm
Product Code :- CLM/PHY/H-077

Description:
• For use as a water turbine to drive a generator producing electricity or for use as a pump driven by a motor and raising a head of water to produce potential energy.
• The rotor has eight ‘bucket’ blades and is housed in a block turbine chamber 50 x 50 x 25 mm with a clear perspex front.
• Two inlet tubules (for turbine and pump operation respectively) and one outlet tubule are provided, and the shaft carries a 15mm diameter pulley.
• With driving belt. Size 15 x 10 cm 
Product Code :- CLM/PHY/H-078

Description:
• Product will be introduced shortly Enquiries will be entertained on REQUEST.
Product Code :- CLM/PHY/H-079

Description:
• To demonstrate principle of lead / acid accumulator.
• Glass jar, 250 ml with plastic screw cap
• Carrying 4 mm socket terminals
• Fitted two lead plate.
Product Code :- CLM/PHY/H-080

Description:
• To show conversion of mechanical energy into electrical energy.
• Turbine with transparent cover • Inlet and outlet tubes
• Directly connected to a dynamo.
• Fitted on base.
• Economy Model
Product Code :- CLM/PHY/H-081

Description:
• Turbine with transparent cover.
• Inlet and outlet tubes.
• Directly connected to a dynamo.
• Fitted on base.
• Superior Model
Product Code :- CLM/PHY/H-082

Description:
• Mounted upon wooden base fitted on stand A single phase energy meter mounted on support, in transparent case to enable students observe the actual movement of the meter. A bulb holder and power cord is supplied in order to observe the working of the meter when power is switched on.
Product Code :- CLM/PHY/H-083

Description:
• Product will be introduced shortly Enquiries will be entertained on REQUEST.
Product Code :- CLM/PHY/H-084