Description:
• This pair of identical wooden trolleys 300 mm long.
• Mounted on three wheels.
• A spring loaded rod is fitted to give impulse when released.
• It has a provision for stacking the trolleys on top of each other with removable pins.
Supplied complete with :-
• 3 elastic rings,
• 3 springs,
• 8 pins (for stacking),
• 2 rubber corks,
• 2 needles and 1 releasing pin.
Product Code :- CLM/PHY/MECH-0155

Descritpion:
• All metal with compact design, dynamic trolley.
• Includes velcro pads for non elastic collisions and locating pins to permit secure stacking of two or more trolleys.
• One end of metal body carries an integral spring plunger/trigger system for explosion experiments whilst the other end has a clamping screw
for attaching ticker tape.
Product Code :- CLM/PHY/MECH-0156

Description:
•  Designed to provide a smooth flat easily inclinable surface for dynamic experiments using trolleys. With wooden sides rails and plastic feets. Size 1.5 x 0.3 meters. Supplied without dynamic trolleys.
Product Code :- CLM/PHY/MECH-0157

Description:
• Stand with 10mm statinless steel mounted rod to hold tape rolls. A specially designed stand to hold our ticket tape rolls, with easy possible, it is an excellent accessory.
Product Code :- CLM/PHY/MECH-0158

Description:
• For attaching to cords for lifting of slotted masses.
• Pack of 10.
Product Code :- CLM/PHY/MECH-0159

Description:
• Wheel And Axle product have wooden double wheel with flat bottomed grooves.
• Diameters are 150 and 50 mm respectively.
• With a spindle for supporting in a retort stand, with two hooks and cord.
• Supplied without stand or masses.
Product Code :- CLM/PHY/MECH-0160

Description:
• Metal wheel with two axles of 50 mm and 25 mm diam.
• Mounted in adjustable steel cones in a cast metal frame, having holes for wall mounting.
• 100 mm diameter of metal wheel.
Product Code :- CLM/PHY/MECH-0161

Description:
• Consists of a wooden block 190 x 58 x 30 mm approx. with a pivoted.
• L-section spring loaded metal launching bar with a trigger catch.
• Showing that horizontal and vertical motions are independent of each other.
• On releasing the catch, one steel ball drops vertically while the other is projected horizontally, both hitting the floor at the same time.
• Supplied with 2 steel balls with storage recess in the block.
Product Code :- CLM/PHY/MECH-0162

Description:
• To demonstrate the principle of conversion of momentum and to show that momentum has direction as well as magnitude.
• Consists of a curved wooden runway 280 x 67 mm length x height with an 8 mm groove, an index mark near top and a slotted metal plate at bottom.
• The apparatus can be fixed to the table with a GClamp (which is not provided).
• A device can be attached to the plate to provide support to the object sphere either exactly opposite the runway.
• Slightly oblique position.
• A plumb bob and 2 steel balls are provided.
Product Code :- CLM/PHY/MECH-0163

Description:
• For accelerating trolleys, length 180 mm, eyelets at both ends, pack of 12.
Product Code :- CLM/PHY/MECH-0165

Description:
• To provide constant accelerating force to dynamics trolley. A pair of metal discs with a tensioning spring mounted on a metal bracket with a handle provides different tensions to the string, providing adjustable but constant force to the trolley. 
Product Code :- CLM/PHY/MECH-0166

Description:
• To provide dots on tape at 1/50 or 1/60 second intervals, equal to the frequency of the mains supply. Operates on12 V a.c. It has an electromagnet & a spring loaded armature which vibrates above a support table. Paper tape, drawn through guides on the table is struck by a dotting screw, carried on the armature. A peg on the table is provided to allow full use of carbon paper disc. Fitted on base.
Product Code :- CLM/PHY/MECH-0167

Description:
• Working on 12 V d.c. supply. Provides dots at 1/50 second intervals.
Product Code :- CLM/PHY/MECH-0168

Description:
• 9 mm width, 300 metre roll.
Product Code :- CLM/PHY/MECH-0169

Description:
• Carbon paper disc, 50 mm dia., box of 100
Product Code :- CLM/PHY/MECH-0170

Description:
• To enable timer CLM/PHY/MECH-0167 to be supported in any desired position. Cast alloy clamp with swivel pad thumb screw, mounted on support rod 100x13 mm.
Product Code :- CLM/PHY/MECH-0171

Description:
•  To change direction of travel, 13 mm wide, 10 mm diam. pulley, mounted on support rod 130 x 10 mm.
Product Code :- CLM/PHY/MECH-0172

Description:
• For ticker tape timer No. CLM/PHY/MECH-0167, input 220-240 V, output 12 V a.c. 1 amp.
Product Code :- CLM/PHY/MECH-0173

Description:
•  Mains operated electronic timer reads 0 to 99.99 seconds. The display comprises of four 7 segment digits to read seconds and centiseconds. Two pairs of colour coded 4 mm sockets with two push buttons are controlled with a mode switch which enables either make or break pulse to be used to operate the timer. With re-set action.
Product Code :- CLM/PHY/MECH-0174

Description:
• For use as a light operated timing gate. It consists of a photo detector and light source, housed in two plastic cases. 4 mm sockets are provided for connecting it to electronic timer gate.
Product Code :- CLM/PHY/MECH-0175

Description:
• Square section aluminium alloy track,length 1.5 m, with staggered holes, supported on two light alloy castings. One support has a two point contact and other a one point contact for lateral and horizontal adjustments by means of a knurled screw. Identical end caps enable air to be introduced from either end of the track keeping the other end closed.
Product Code :- CLM/PHY/MECH-0176

Consisting of :
• 2 Large vehicles (mass 400 gm.,length 215 mm)
• 1 Small vehicle (mass 200 gm.,length 100 mm)
• 2 Magnetic buffers (25 mm diam.)
• 2 Plasticine Holders(20 mm diam.) with central hole
• 4 Catapults(45 mm wide) with slots for elastic band
• 1 Reel of nylon thread
• 2 White rods(4 mm diam.150 mm long)
• 24 Needles
• 20 White plain cards
• 1 Reel rubber strand
• 1 Pack of plasticine
• 20 Elastic bands 1 Instruction manual 
Product Code :- CLM/PHY/MECH-0177

Description:
• Aluminium alloy square section rule incorporating four different faces for use with linear air track.
Product Code :- CLM/PHY/MECH-0178

Description:
•  Suitable for use with linear air track. With a flexible hose terminating in a tapered adapter.230V a.c., 50 Hz.
Product Code :- CLM/PHY/MECH-0179

Description:
•  A metal bar 25 cm long with threaded ends and removable threaded discs, with a split chuck in middle.
Product Code :- CLM/PHY/MECH-0180

Description:
•  To show that the torque required to accelerate a flywheel depends upon its moment of inertia rather than its mass.A steel bar 790x12 mm is mounted at its center on a sleeved spindle. The spindle is extended through a sleeve so that the bar may be rotated by a weight and string. Heavy adjustable masses are mounted on each end of the bar and may be clamped at any desired position enabling inertia to be varied.
Product Code :- CLM/PHY/MECH-0181

Description:
•  Quartz timer, showing normal time, hours, minutes, seconds, days, dates, months are displayed. 1/100th second, with alarm.
Product Code :- CLM/PHY/MECH-0182

Description:
•  Smithtype, encased in a metal case with fly-back action. At the right side case is the stop and start lever, the operation of which enables a timer start and stopped as desired. On the other side of the case is a press which returns the hands to zero, after the mechanism has been stopped means of a stop lever. A subsidiary dial recording 0 to 60 minutes is below the second hand. It comes with least count of second.
Product Code :- CLM/PHY/MECH-0183